Wiki

How to remove a link from a watch in 10 easy steps

Want to know how to remove a link from a watch? It’s not as difficult as you think. It can be a daunting task at first, just like How to Clean an iPhone’s Charging Port or How to Clean iPhone Speakers, but totally worth it. After all, there’s nothing more frustrating than a loose metal bracelet rubbing your wrist. Some may be so loose that the watch face itself is on the wrong side – not an ideal look for a watch. best smart watch.

If your watch isn’t worn properly, you really don’t have to put up with it. With just a few handy tools and a few minutes of care and attention, your watch can fit like a glove. Here we’ll walk you through what you need to do step by step so you don’t have to pay a professional to do it.

what will you need

watch tool box

OR

pin driver/screwdriver

Hammer (optional)

pliers

a. First you will want find a place to do it with lots of light. It’s also a good idea to have a tray to hold parts and a small bag to store spare rings.

2nd. Now, keep the watch in place on your wrist you want to wear it. Gather the excess links at the bottom and Count how many links you can bear to remove. Don’t forget that you’ll need a little breathing room on your wrist, so be careful if you’re not sure an extra tie is too tight.

3. Check this number before proceeding to the next step.

4. Divide this number by two so you know how many links to remove from each side of the loop. You will want to hold it so that the loop is in the middle.

A pin removed from a metal watch strap using a pin pusher

(Image credit: Shutterstock)

5. EZTool Watch Repair Kit ($19.87, Amazon), then it probably comes with a clock support. Take a look at the underside of your metal bracelet. You should see a few small arrows on the links closest to the loop. Place the watch in the holder with the arrows pointing down. These basically represent the direction in which you should remove the pins. If you don’t see any arrows, your pins may be a screw head, then skip to step 7.

6. later you want place the pin pusher on the pin For the number of relevant links you want to remove, remember that you want to remove half from each side of the clasp. Then, using the hammer provided (a regular hammer can also work if you’re careful), lightly press the pusher until you can push no further enter the link. Turn your watch and loosen the pin on the other side using a pair of tweezers with your fingers. Be prepared for the connections to be loose and the ferrules to loosen as well. Don’t lose any pins or rings – keep them handy on a tray.

7. Depending on your watch, the pins can have a screw head, in which case you will need to use a 1mm screwdriver to remove them. Turn the pins counterclockwise and use pliers to pull them out.

8. you want immediately repeat this method on both sides for the buckle itself and the number of fasteners you wish to remove from the other side of the strap.

9. Set aside excess connections in the bag. You are now ready to put the clasp back on. Rotate the clock in your clock holder so the arrows are now pointing up.

A pin in place on a metal watch strap

(Image credit: Shutterstock)

ten. you need now tie the ties to the loop reinserting the pins in the direction you removed them. After aligning the clasp and eyelets, insert the pins into the holes and tap them lightly with the hammer until they snap back into place. You can also screw them in place if you used a screwdriver to remove them.

That’s it, your watch strap should now fit perfectly. Don’t forget to keep spare rings and pins in case you need them in the future.


For more DIY tips, tricks and how-to’s, check out our guides on how to fix a leaky bathtub faucet, install laminate flooring and make your washing machine last longer and need fewer repairs.



See more

How to remove a link from a watch in 10 easy steps

Want to know how to remove a link from a watch? It’s not as tricky as you might think. It can be an intimidating task at first, much like how to clean an iPhone’s charging port or how to clean iPhone speakers, but it’s definitely worth doing. After all, there’s nothing as frustrating as a loose metal strap rubbing your wrist. Some can be so loose that the watch face itself ends up on the wrong side — not an ideal look  for the best smartwatch. 
If your watch isn’t fitted correctly, you really don’t need to endure it. With just a few useful tools and a couple of minutes of care and attention, your watch can fit like a glove. Here, we will take you through what you need to do step-by-step, so you don’t need to pay for a pro to do it.
How to remove a link from a watch  
What you’ll need
Watch tool kit
OR
Pin pusher/screwdriver
Hammer (optional)
Pliers
1. First, you will want to find somewhere to do this with plenty of light. It’s also a good idea to have a tray on hand to hold the parts and a small bag to store the spare links.
2. Now, hold the watch in place on the wrist you want to wear it. Gather up the excess links on the underside and count out how many links you could stand to remove. Remember, you’ll want a little breathing space on your wrist, so if you’re not sure if one extra link might be too tight, air on the side of caution.
3. Double check this number before proceeding to the next step. 
4. Divide this number by two so you know how many links you’re going to remove from each side of the clasp. You’ll want to keep this even so the clasp sits central. 

(Image credit: Shutterstock)
5. If you’re using a watch tool kit, such as the EZTool Watch Repair Kit ($19.87, Amazon), then it likely comes with a watch holder. Take a look at the underside of your metal strap. You should notice some small arrows on the links nearest the clasp. Place the watch in the holder with those arrows pointing downwards. These essentially represent the direction you should remove the pins. If you can’t see any arrows, your pins may be a screw head, in which case move onto step 7. 
6. You then want to insert the pin pusher over the pin for the relevant number of links you want to remove — remember, you want to remove half on each side of the clasp. Then, using the included hammer (a regular hammer can also work if you’re careful), lightly tap the pin pusher until you can’t push it any further into the link. Rotate your watch and pull the pin loose from the other side using a pair of pliers of your fingers. Be ready for the links to fall free and watch out for ferrules falling loose too. Don’t lose the pins or ferrules — keep them to hand on a tray. 
7. Depending on your watch, the pins may have a screw head, in which case you’ll want to use a 1mm screwdriver to remove these instead. Simply turn the pins counterclockwise and use pliers to remove.  
8. You’ll want to repeat this method on both immediate sides of the clasp itself as well as for the number of links you want to remove on the other side of the strap. 
9. Set the excess links aside in a bag. Now you’re ready to refit the clasp. Rotate the watch in your watch holder so the arrows now point upwards. 

(Image credit: Shutterstock)
10. You now need to connect the links to the clasp by reinserting the pins from the direction that you knocked them out. Place the pins in the holes after lining up the clasp and any ferrules, and gently tap them with the hammer until they’re knocked back into place. Alternatively, screw them back into a place if you used a screwdriver to remove.
And that’s it, your watch strap should now fit you perfectly. Remember to keep the spare links and pins in case you should ever need them in the future.
For more DIY tips, tricks, and how-tos, check out our guides on how to repair a leaky bathtub faucet, how to install laminate flooring and how to make your washing machine last longer and need fewer repairs.   

#remove #link #watch #easy #steps

How to remove a link from a watch in 10 easy steps

Want to know how to remove a link from a watch? It’s not as tricky as you might think. It can be an intimidating task at first, much like how to clean an iPhone’s charging port or how to clean iPhone speakers, but it’s definitely worth doing. After all, there’s nothing as frustrating as a loose metal strap rubbing your wrist. Some can be so loose that the watch face itself ends up on the wrong side — not an ideal look  for the best smartwatch. 
If your watch isn’t fitted correctly, you really don’t need to endure it. With just a few useful tools and a couple of minutes of care and attention, your watch can fit like a glove. Here, we will take you through what you need to do step-by-step, so you don’t need to pay for a pro to do it.
How to remove a link from a watch  
What you’ll need
Watch tool kit
OR
Pin pusher/screwdriver
Hammer (optional)
Pliers
1. First, you will want to find somewhere to do this with plenty of light. It’s also a good idea to have a tray on hand to hold the parts and a small bag to store the spare links.
2. Now, hold the watch in place on the wrist you want to wear it. Gather up the excess links on the underside and count out how many links you could stand to remove. Remember, you’ll want a little breathing space on your wrist, so if you’re not sure if one extra link might be too tight, air on the side of caution.
3. Double check this number before proceeding to the next step. 
4. Divide this number by two so you know how many links you’re going to remove from each side of the clasp. You’ll want to keep this even so the clasp sits central. 

(Image credit: Shutterstock)
5. If you’re using a watch tool kit, such as the EZTool Watch Repair Kit ($19.87, Amazon), then it likely comes with a watch holder. Take a look at the underside of your metal strap. You should notice some small arrows on the links nearest the clasp. Place the watch in the holder with those arrows pointing downwards. These essentially represent the direction you should remove the pins. If you can’t see any arrows, your pins may be a screw head, in which case move onto step 7. 
6. You then want to insert the pin pusher over the pin for the relevant number of links you want to remove — remember, you want to remove half on each side of the clasp. Then, using the included hammer (a regular hammer can also work if you’re careful), lightly tap the pin pusher until you can’t push it any further into the link. Rotate your watch and pull the pin loose from the other side using a pair of pliers of your fingers. Be ready for the links to fall free and watch out for ferrules falling loose too. Don’t lose the pins or ferrules — keep them to hand on a tray. 
7. Depending on your watch, the pins may have a screw head, in which case you’ll want to use a 1mm screwdriver to remove these instead. Simply turn the pins counterclockwise and use pliers to remove.  
8. You’ll want to repeat this method on both immediate sides of the clasp itself as well as for the number of links you want to remove on the other side of the strap. 
9. Set the excess links aside in a bag. Now you’re ready to refit the clasp. Rotate the watch in your watch holder so the arrows now point upwards. 

(Image credit: Shutterstock)
10. You now need to connect the links to the clasp by reinserting the pins from the direction that you knocked them out. Place the pins in the holes after lining up the clasp and any ferrules, and gently tap them with the hammer until they’re knocked back into place. Alternatively, screw them back into a place if you used a screwdriver to remove.
And that’s it, your watch strap should now fit you perfectly. Remember to keep the spare links and pins in case you should ever need them in the future.
For more DIY tips, tricks, and how-tos, check out our guides on how to repair a leaky bathtub faucet, how to install laminate flooring and how to make your washing machine last longer and need fewer repairs.   

#remove #link #watch #easy #steps


Synthetic: Ôn Thi HSG

Trả lời

Email của bạn sẽ không được hiển thị công khai. Các trường bắt buộc được đánh dấu *

Back to top button